OPEN SOURCE Bionics Arm Project

from __future__ import print_function

import enum
import re
import os
import struct
import sys
import threading
import time
import queue
import serial
from serial.tools.list_ports import comports

from common import *
#import thread,queue


#sudo python3 /home/bionic/Desktop/python/myo_raw.py


# importing the requests library 
import requests 
  
requestQueue = queue.Queue()


def processGetRequest():
    while True:
        item = requestQueue.get()     
        requests.get(url=item["url"],params=item["params"])
        requestQueue.task_done()

requestProcessor = threading.Thread(target=processGetRequest)
requestProcessor.daemon = True
requestProcessor.start()

  
# api-endpoint 
URL = "http://127.0.0.1/bionic/input"
numpy = 0  
numPod = 0
# location given here 
#location = "delhi technological university"
  
# defining a params dict for the parameters to be sent to the API 
#PARAMS = {'address':location} 
  
# sending get request and saving the response as response object 
#r = requests.get(url = URL, params = PARAMS) 
  
# extracting data in json format 
#data = r.json() 
##def OLDsendEMG(URL,PARAMS):
 ##requestQueue.put({"url":URL,"params":PARAMS})
 
	  
def sendEMG(URL,PARAMS):
  global numpy
  global numPod
  numpy += 1
  numPod += 1
	#  r = requests.get(url = URL, params = PARAMS)
  if numPod > 8:
     numPod = 1
     if numpy > 850:
      numpy = 1 
      requestQueue.put({"url":URL,"params":PARAMS})
 
  
# extracting latitude, longitude and formatted address  
# of the first matching location 
#latitude = data['results'][0]['geometry']['location']['lat'] 
#longitude = data['results'][0]['geometry']['location']['lng'] 
#formatted_address = data['results'][0]['formatted_address'] 
  



def multichr(ords):
    if sys.version_info[0] >= 3:
        return bytes(ords)
    else:
        return ''.join(map(chr, ords))

def multiord(b):
    if sys.version_info[0] >= 3:
        return list(b)
    else:
        return map(ord, b)

class Arm(enum.Enum):
    UNKNOWN = 0
    RIGHT = 1
    LEFT = 2

class XDirection(enum.Enum):
    UNKNOWN = 0
    X_TOWARD_WRIST = 1
    X_TOWARD_ELBOW = 2

class Pose(enum.Enum):
    REST = 0
    FIST = 1
    WAVE_IN = 2
    WAVE_OUT = 3
    FINGERS_SPREAD = 4
    THUMB_TO_PINKY = 5
    UNKNOWN = 255


class Packet(object):
    def __init__(self, ords):
        self.typ = ords[0]
        self.cls = ords[2]
        self.cmd = ords[3]
        self.payload = multichr(ords[4:])

    def __repr__(self):
        return 'Packet(%02X, %02X, %02X, [%s])' % \
            (self.typ, self.cls, self.cmd,
             ' '.join('%02X' % b for b in multiord(self.payload)))


class BT(object):
    '''Implements the non-Myo-specific details of the Bluetooth protocol.'''
    def __init__(self, tty):
        self.ser = serial.Serial(port=tty, baudrate=9600, dsrdtr=1)
        self.buf = []
        self.lock = threading.Lock()
        self.handlers = []

    ## internal data-handling methods
    def recv_packet(self, timeout=None):
        t0 = time.time()
        self.ser.timeout = None
        while timeout is None or time.time() < t0 + timeout:
            if timeout is not None: self.ser.timeout = t0 + timeout - time.time()
            c = self.ser.read()
            if not c: os.system("python3 /home/bionic/Desktop/python/myo_raw.py")
 
 
            if c == 0: os.system("python3 /home/bionic/Desktop/python/myo_raw.py")
			
            ret = self.proc_byte(ord(c))
            if ret:
                if ret.typ == 0x80:
                    self.handle_event(ret)
                return ret

    def recv_packets(self, timeout=.5):
        res = []
        t0 = time.time()
        while time.time() < t0 + timeout:
            p = self.recv_packet(t0 + timeout - time.time())
            if not p: return res
            res.append(p)
        return res

    def proc_byte(self, c):
        if not self.buf:
            if c in [0x00, 0x80, 0x08, 0x88]:
                self.buf.append(c)
            return None
        elif len(self.buf) == 1:
            self.buf.append(c)
            self.packet_len = 4 + (self.buf[0] & 0x07) + self.buf[1]
            return None
        else:
            self.buf.append(c)

        if self.packet_len and len(self.buf) == self.packet_len:
            p = Packet(self.buf)
            self.buf = []
            return p
        return None

    def handle_event(self, p):
        for h in self.handlers:
            h(p)

    def add_handler(self, h):
        self.handlers.append(h)

    def remove_handler(self, h):
        try: self.handlers.remove(h)
        except ValueError: pass

    def wait_event(self, cls, cmd):
        res = [None]
        def h(p):
            if p.cls == cls and p.cmd == cmd:
                res[0] = p
        self.add_handler(h)
        while res[0] is None:
            self.recv_packet()
        self.remove_handler(h)
        return res[0]

    ## specific BLE commands
    def connect(self, addr):
        return self.send_command(6, 3, pack('6sBHHHH', multichr(addr), 0, 6, 6, 64, 0))

    def get_connections(self):
        return self.send_command(0, 6)

    def discover(self):
        return self.send_command(6, 2, b'\x01')

    def end_scan(self):
        return self.send_command(6, 4)

    def disconnect(self, h):
        return self.send_command(3, 0, pack('B', h))

    def read_attr(self, con, attr):
        self.send_command(4, 4, pack('BH', con, attr))
        return self.wait_event(4, 5)

    def write_attr(self, con, attr, val):
        self.send_command(4, 5, pack('BHB', con, attr, len(val)) + val)
        return self.wait_event(4, 1)

    def send_command(self, cls, cmd, payload=b'', wait_resp=True):
        s = pack('4B', 0, len(payload), cls, cmd) + payload
        self.ser.write(s)

        while True:
            p = self.recv_packet()

            ## no timeout, so p won't be None
            if p.typ == 0: return p

            ## not a response: must be an event
            self.handle_event(p)


class MyoRaw(object):
    '''Implements the Myo-specific communication protocol.'''

    def __init__(self, tty=None):
        if tty is None:
            tty = self.detect_tty()
        if tty is None:
            raise ValueError('Myo dongle not found!')

        self.bt = BT(tty)
        self.conn = None
        self.emg_handlers = []
        self.imu_handlers = []
        self.arm_handlers = []
        self.pose_handlers = []

    def detect_tty(self):
        for p in comports():
            if re.search(r'PID=2458:0*1', p[2]):
                print('using device:', p[0])
                return p[0]

        return None

    def run(self, timeout=None):
        self.bt.recv_packet(timeout)

    def connect(self):
        ## stop everything from before
        self.bt.end_scan()
        self.bt.disconnect(0)
        self.bt.disconnect(1)
        self.bt.disconnect(2)

        ## start scanning
        print('scanning...')
        self.bt.discover()
        while True:
            p = self.bt.recv_packet()
            print('scan response:', p)

            if p.payload.endswith(b'\x06\x42\x48\x12\x4A\x7F\x2C\x48\x47\xB9\xDE\x04\xA9\x01\x00\x06\xD5'):
                addr = list(multiord(p.payload[2:8]))
                break
        self.bt.end_scan()

        ## connect and wait for status event
        conn_pkt = self.bt.connect(addr)
        self.conn = multiord(conn_pkt.payload)[-1]
        self.bt.wait_event(3, 0)

        ## get firmware version
        fw = self.read_attr(0x17)
        _, _, _, _, v0, v1, v2, v3 = unpack('BHBBHHHH', fw.payload)
        print('firmware version: %d.%d.%d.%d' % (v0, v1, v2, v3))

        self.old = (v0 == 0)

        if self.old:
            ## don't know what these do; Myo Connect sends them, though we get data
            ## fine without them
            self.write_attr(0x19, b'\x01\x02\x00\x00')
            self.write_attr(0x2f, b'\x01\x00')
            self.write_attr(0x2c, b'\x01\x00')
            self.write_attr(0x32, b'\x01\x00')
            self.write_attr(0x35, b'\x01\x00')

            ## enable EMG data
            self.write_attr(0x28, b'\x01\x00')
            ## enable IMU data
            self.write_attr(0x1d, b'\x01\x00')

            ## Sampling rate of the underlying EMG sensor, capped to 1000. If it's
            ## less than 1000, emg_hz is correct. If it is greater, the actual
            ## framerate starts dropping inversely. Also, if this is much less than
            ## 1000, EMG data becomes slower to respond to changes. In conclusion,
            ## 1000 is probably a good value.
            C = 1000
            emg_hz = 50
            ## strength of low-pass filtering of EMG data
            emg_smooth = 100

            imu_hz = 50

            ## send sensor parameters, or we don't get any data
            self.write_attr(0x19, pack('BBBBHBBBBB', 2, 9, 2, 1, C, emg_smooth, C // emg_hz, imu_hz, 0, 0))

        else:
            name = self.read_attr(0x03)
            print('device name: %s' % name.payload)

            ## enable IMU data
            self.write_attr(0x1d, b'\x01\x00')
            ## enable on/off arm notifications
            self.write_attr(0x24, b'\x02\x00')

            # self.write_attr(0x19, b'\x01\x03\x00\x01\x01')
            self.start_raw()

        ## add data handlers
        def handle_data(p):
            if (p.cls, p.cmd) != (4, 5): return

            c, attr, typ = unpack('BHB', p.payload[:4])
            pay = p.payload[5:]

            if attr == 0x27:
                vals = unpack('8HB', pay)
                ## not entirely sure what the last byte is, but it's a bitmask that
                ## seems to indicate which sensors think they're being moved around or
                ## something
                emg = vals[:8]
                moving = vals[8]
                self.on_emg(emg, moving)
            elif attr == 0x1c:
                vals = unpack('10h', pay)
                quat = vals[:4]
                acc = vals[4:7]
                gyro = vals[7:10]
                self.on_imu(quat, acc, gyro)
            elif attr == 0x23:
                typ, val, xdir = unpack('8', pay)

                if typ == 1: # on '
                    self.on_arm(Arm(val), XDirection(xdir))
                elif typ == 2: # removed from arm
                    self.on_arm(Arm.UNKNOWN, XDirection.UNKNOWN)
                elif typ == 3: # pose
                    self.on_pose(Pose(val))
            else:
                print('data with unknown attr: %02X %s' % (attr, p))

        self.bt.add_handler(handle_data)


    def write_attr(self, attr, val):
        if self.conn is not None:
            self.bt.write_attr(self.conn, attr, val)

    def read_attr(self, attr):
        if self.conn is not None:
            return self.bt.read_attr(self.conn, attr)
        return None



    def disconnect(self):
        if self.conn is not None:
            self.bt.disconnect(self.conn)

    def start_raw(self):
        '''Sending this sequence for v1.0 firmware seems to enable both raw data and
        pose notifications.
        '''

        self.write_attr(0x28, b'\x01\x00')
        self.write_attr(0x19, b'\x01\x03\x01\x01\x00')
        self.write_attr(0x19, b'\x01\x03\x01\x01\x01')

    def mc_start_collection(self):
        '''Myo Connect sends this sequence (or a reordering) when starting data
        collection for v1.0 firmware; this enables raw data but disables arm and
        pose notifications.
        '''

        self.write_attr(0x28, b'\x01\x00')
        self.write_attr(0x1d, b'\x01\x00')
        self.write_attr(0x24, b'\x02\x00')
        self.write_attr(0x19, b'\x01\x03\x01\x01\x01')
        self.write_attr(0x28, b'\x01\x00')
        self.write_attr(0x1d, b'\x01\x00')
        self.write_attr(0x19, b'\x09\x01\x01\x00\x00')
        self.write_attr(0x1d, b'\x01\x00')
        self.write_attr(0x19, b'\x01\x03\x00\x01\x00')
        self.write_attr(0x28, b'\x01\x00')
        self.write_attr(0x1d, b'\x01\x00')
        self.write_attr(0x19, b'\x01\x03\x01\x01\x00')

    def mc_end_collection(self):
        '''Myo Connect sends this sequence (or a reordering) when ending data collection
        for v1.0 firmware; this reenables arm and pose notifications, but
        doesn't disable raw data.
        '''

        self.write_attr(0x28, b'\x01\x00')
        self.write_attr(0x1d, b'\x01\x00')
        self.write_attr(0x24, b'\x02\x00')
        self.write_attr(0x19, b'\x01\x03\x01\x01\x01')
        self.write_attr(0x19, b'\x09\x01\x00\x00\x00')
        self.write_attr(0x1d, b'\x01\x00')
        self.write_attr(0x24, b'\x02\x00')
        self.write_attr(0x19, b'\x01\x03\x00\x01\x01')
        self.write_attr(0x28, b'\x01\x00')
        self.write_attr(0x1d, b'\x01\x00')
        self.write_attr(0x24, b'\x02\x00')
        self.write_attr(0x19, b'\x01\x03\x01\x01\x01')

    def vibrate(self, length):
        if length in xrange(1, 4):
            ## first byte tells it to vibrate; purpose of second byte is unknown
            self.write_attr(0x19, pack('3B', 3, 1, length))


    def add_emg_handler(self, h):
        self.emg_handlers.append(h)

    def add_imu_handler(self, h):
        self.imu_handlers.append(h)

    def add_pose_handler(self, h):
        self.pose_handlers.append(h)

    def add_arm_handler(self, h):
        self.arm_handlers.append(h)


    def on_emg(self, emg, moving):
        for h in self.emg_handlers:
            h(emg, moving)

    def on_imu(self, quat, acc, gyro):
        for h in self.imu_handlers:
            h(quat, acc, gyro)

    def on_pose(self, p):
        for h in self.pose_handlers:
            h(p)

    def on_arm(self, arm, xdir):
        for h in self.arm_handlers:
            h(arm, xdir)


if __name__ == '__main__':
 while True:
    try:
        import pygame
        from pygame.locals import *
        HAVE_PYGAME = True
    except ImportError:
        HAVE_PYGAME = False

    if HAVE_PYGAME:
        w, h = 1200, 400
        scr = pygame.display.set_mode((w, h))

    last_vals = None
    def plot(scr, vals):
        DRAW_LINES = False

        global last_vals
        if last_vals is None:
            last_vals = vals
            return

        D = 5
        scr.scroll(-D)
        scr.fill((0,0,0), (w - D, 0, w, h))
        for i, (u, v) in enumerate(zip(last_vals, vals)):
            if DRAW_LINES:
                pygame.draw.line(scr, (0,255,0),
                                 (w - D, int(h/8 * (i+1 - u))),
                                 (w, int(h/8 * (i+1 - v))))
                pygame.draw.line(scr, (255,255,255),
                                 (w - D, int(h/8 * (i+1))),
                                 (w, int(h/8 * (i+1))))
            else:
                c = int(255 * max(0, min(1, v)))
                scr.fill((c, c, c), (w - D, i * h / 8, D, (i + 1) * h / 8 - i * h / 8));

        pygame.display.flip()
        last_vals = vals

    m = MyoRaw(sys.argv[1] if len(sys.argv) >= 2 else None)

    def proc_emg(emg, moving, times=[]):
	
        if HAVE_PYGAME:
            ## update pygame display
            plot(scr, [e / 2000. for e in emg])
        else:
            print(emg)

            for emgpod in emg:
            ## print(emgpod);
             PARAMS = {'pod_data': emgpod } 
##             PARAMS = {'pod_data':emgpod,'pod_num':emgnum} 
             ##requestQueue.put({"url":URL,"params":PARAMS})
             sendEMG(URL,PARAMS) 
        ## print framerate of received data
        times.append(time.time())
        if len(times) > 20:
            #print((len(times) - 1) / (times[-1] - times[0]))
            times.pop(0)

    m.add_emg_handler(proc_emg)
    m.connect()

    m.add_arm_handler(lambda arm, xdir: print('arm', arm, 'xdir', xdir))
    m.add_pose_handler(lambda p: print('pose', p))

    try:
        while True:
            m.run(1)

            if HAVE_PYGAME:
                for ev in pygame.event.get():
                    if ev.type == QUIT or (ev.type == KEYDOWN and ev.unicode == 'q'):
                        raise KeyboardInterrupt()
                    elif ev.type == KEYDOWN:
                        if K_1 <= ev.key <= K_3:
                            m.vibrate(ev.key - K_0)
                        if K_KP1 <= ev.key <= K_KP3:
                            m.vibrate(ev.key - K_KP0)

    except KeyboardInterrupt:
        pass
    finally:
        m.disconnect()
        print()