Hardware and Software products

The PicoZed™ FMC Carrier Card V2 is the 2nd generation FMC Carrier supporting the PicoZed System-on-Module. This Carrier supports develop...

The Pi PoE Switch HAT is an add-on board for the Raspberry Pi that brings the Pi Supply Switch technology together with PoE.

M5Stack NEW Corner Connector for 1515 Aluminum Profile (10pcs a set)

Web-based remote desktop on cloud servers pre-installed with FPGA design software and licenses for research and development needs.

The Pmod ACL2 is a 3-axis MEMS accelerometer powered by the Analog Devices ADXL362.

The Pmod AD5 is an ADC that utilizes a fourth order sigma-delta modulator, a programmable gain array, and on-chip digital filtering.

The Pmod BB provides a ready-made solution for prototyping breadboard circuits.

This kit is a handy accompaniment to your 12-pin Pmod.

The extension cable lets you locate your Pmod away from its host board, and the included male gender changer provides extra connectivity.

The Pmod CDC1 is a capacitative sensor that uses the Analog Devices AD7156.

The Pmod CON1 has two terminals that can be used to provide power from an outside source and the other four can be used for data signals.

The Pmod DA2 is a 12-bit digital-to-analog converter powered by the Texas Instruments DAC121S101.

The Pmod DA3 is a 16-bit digital-to-analog converter powered by the Analog Devices AD5541A.

The Pmod DPG1 is a differential pressure gauge module.

The Pmod HB5 offers a 2A H-bridge circuit to drive small to medium sized DC motors.

The Pmod ISNS20 is a small current sense module with a digital SPI interface that is quick, accurate, and used for a variety of applications

The Pmod LED has four user LEDs that are individually driven through logic-level transistors.

The Pmod OC1 is an open collector BJT module using MMBT3904 transistors.

The Pmod OD1 is an open drain FET module using NTHD4508 transistors.

The Pmod R2R is resistor ladder with a R-2R resistor configuration.

The Pmod RS232 converts between digital logic voltage levels to RS232 voltage levels.

The Pmod SSD is a 2-digit 7-segment display that can toggle through GPIO signals and achieve persistence-of-vision.

The Pmod TMP3 is an ambient temperature sensor built around the Microchip TCN75A.

The POE-GEVB demonstrates the NCP1083, a member of the Power over Ethernet Powered Device (PoE-PD) product family.

Power Supply for general project use.

For connecting probes with male BNC leads.

Allows you to easily hook up an oscilloscope or logic analyzer

An inexpensive and convenient way to add personalized and custom hardware to your Pi-Plates based project.

The CY8CKIT-043 PSoC 4® M-Series Prototyping Kit is a low-cost platform for prototyping products using the PSoC 4 M-Series device family, wi

Charge your Crazyflie 2.0 without plugging in a USB cable

The Qwiic Ideation Kit is the smorgasbord of our best and most popular Qwiic boards. This kit allows users to get started with Arduino wi...

The RAK14000 module is part of the WisBlock IO series, the RAK14000 is an Active Matrix Electrophoretic Display (AM EPD) module.

The RAK2247 is the evolution of RAK833. It retains the same small form factor (mPCIE) and is just as easy to integrate as the previous model

This product is now EOL

The RAK5205 LoRa tracker board is built upon the RAK811.

WisNode Lora/LoRaWAN Module,Support AS923, 868/915MHz, LoRa/TTN, Open source LoRa, RAK811 development board, LoRa Arduino shield

Raspberry Pi 3 Model B is the first module of the third-generation Raspberry Pi with Bluetooth 4.1 and Wifi.

There’s a lot of Raspberry Pi information going around lately. Whether it’s Pi A, A+, B, B+, or Pi 2 B, any forum will have thousands of ...

HIFI DAC+ Digital Audio Card Pinboard designed For Raspberry PI 2 Model B +, adopt high-end DAC chip PCM5122 of TI Company.

Perfect for anyone who loves tech, wants a new geeky challenge or build their own personal Internet of Things.

Lets you receive digital DVB-T2 TV streams on your Raspberry Pi

The Blackboard is an ARM and FPGA development board designed specifically for electrical and computer engineering education.

An evaluation board developed by PHYTEC based on the Nordic Semiconductor nRF52840 SoC with Zephyr Project OS

This is a linear microphone array kit for raspberry pi which comes with four microphones and designed for AI and voice applications.

The Grove extension board can be stacked (connected) right onto the top of ReSpeaker Mic Array, bringing even more possibilities.

The reTerminal E10-1 is an expansion board for the reTerminal which empowers it rechargeable and portable functions, enhanced wireless commu

RiTFT-50-IOT-UX is the first-ever IoT display on the market.

Oh oh oh, put together a kit that shows you the journey of Santa Claus!

There is a new robot crawling into town and they call it Antsy!

This kit has everything you need to build a fully programmable rover robot!

If you are looking for a solenoid for your DIY, educational, or Arduino solenoid project the RobotGeek solenoids are a great choice.

Want to make your project kick into gear when life turns up the heat? The RobotGeek Temperature Sensor can feel its way through!

This super strong, high quality, beautifully designed router /spindle mount is the perfect addition to your build!

RS485 is a unit used for converting TTL level to RS485 level.

Equipped with 32-bit microcomputer RX family RX72N, GUI creation using LCD, HMI development, and IoT device development

Access serial, analog, or digital I/O data over Ethernet!

A whole heap of LED pixels with individual brightness control, for scrolling messages, animations, and more - Scroll pHAT HD!

It is a tiny IoT dev board with pre-soldered pins, Wi-Fi, Bluetooth 5.0, 4 power modes, and Arduino/CircuitPython support.