Hardware and Software products

Electrically isolated carrier board for Atlas Scientific EZO line of sensors.

400 Points Breadboard with 2 Positive & Negative Power Lines on both ends.

Stepper motor with a standard interface, when used directly pluggable.

The cheapest and most basic MEGA2560 R3 kit for the beginner.

8GB Micro SD card with Adapter pre-loaded with NOOBS. Easily boot up your Raspberry Pi and select the operating system of your choice.

Narrow type, for 3 small modules (e.g. Mini Battery, Core and Mini Cover Modules).

ENCODER is a rotary encoder module in the FACES series. it need to stack FACES base and M5Core to use.

It is an ePaper Driver Board for XIAO, featuring a 24-pin FPC connector, charging IC, and BAT connector, ideal for Wi-Fi digital frames.

Puck.js is an intelligent Bluetooth button. Software can be uploaded, debugged and modified wirelessly from any modern computer or phone.

Everything you need pre-installed on the device - just plug in via USB and start writing JavaScript code immediately!

Add an Ethernet port to your Omega

The EZ-B v4/2 Wi-Fi Robot Controller is the next generation brain of your robot or IoT device, powering over 20,000 robots worldwide!

An embedded flow meter totalizer module.

An embedded resistance temperature detector (RTD) sensor module.

The FAN2502/03 family utilize CMOS technology to offer extremely low power consumption, shutdown current, and dropout voltage.

This is the FemtoBuck, a small-size single-output constant current LED driver. Each FemtoBuck has the capability to dim a single high-pow...

Raspberry Pi 2 Model B compatible HAT with on-board Gadgeteer-style sockets.

FEZ Spider II is a .NET Gadgeteer-compatible Mainboard.

Everything you need to get started with .NET Gadgeteer-technology.

Friendly and easy to use firmware loader using CMSIS-DAP debuggers.

Spice up your Flick HAT and Raspberry Pi with a stylish white and orange Flick HAT case!

Swipe, tap or flick your wrist to control your Raspberry Pi with the Flick pHAT.

FLIR is a module which integrates lwir micro thermal camera (Lepton 3.0) supplied by FLIR company. Real-time access to non-contact temperatu

Optical flow breakout board for motion detection

Enable positioning in the air with optical motion detection

Get rid of that wireless stack radio tower for Arduino with Flutter. One Platform instead of three (UNO, XBee Shield, XBee Pro)

The Analog Discovery signal cable assembly, or flywire, is the same assembly that ships with every Analog Discovery we sell.

The FMC-HDMI extends FMC-compatible FPGA systems with two HDMI Type A input ports.

M5Stack FRAME Panel Extended Install Components (2 Sets)

An open source, flexible, secure Internet of Things (IoT) development framework, useful to build and manage modern smart spaces.

The FUSB303 device is a fully autonomous USB Type−C™ controller optimized for 15 W or less applications

The Galaxia® Tile is developed to be designed into missions or more advanced prototyping  / testing solution

GameBender is a radical new game console, where you modify ("bend") games while you play them.

3.3V Uniform Sector Dual and Quad Serial Flash

gen4 3.2" Picaso Intelligent Display Module

The Genesys 2 board is an advanced, high-performance, ready-to-use digital circuit development platform based on the powerful Kintex-7 FPGA,

You must have used a GPS receiver. It is easy to be found in most places, such as smartphones, cars, and computers.

This DFRobot 386AMP audio amplifier module uses the National Semiconductor LM386 audio power amplifier chip. It has 20 voltage gain.

This is an Arduino hydrogen gas sensor. It has high sensitivity to Hydrogen (H2) and less sensitivity to alcohol, LPG,cooking fumes .

Communication with the Analog ORP Meter is done using only simple wiring and programing.

The Gravity Conductivity Sensor Switch module can be used to detect if an object has electrical conductivity.

It is an electric switch that is actuated by very little physical force.

what's the best way to detect the magnet? Use anther magnet. But it's not sensitive enough.

The microwave sensor applies the Doppler effect to detect moving objects using microwaves.

The DFRobot Vibration Sensor buffers a piezoelectric transducer that responds to strain changes by generating a measurable output voltage

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board.

This Gravity: I2C HUB module is designed to connect up to 8 I2C devices to the main controller.

This device is based around a MEMS LIS2DH chip solution and has high-performance ultra-low power mode.

If you still don’t know how to play Internet of Things (IoT), the DFRobot OBLOQ module will be ideal for connecting you to the IoT world.

The Grove - 10A DC Current Sensor (ACS725) is a high precision DC current sensor based on ACS725.

Instead of using coil, packaged solid-state relays(SSR) use power semiconductor devices such as thyristors and transistors.

The Grove - 3-Axis Digital Accelerometer ±200g (ADXL372) is an ultra-low-power digital output MEMS Accelerometer.

The Grove - 5-Way Switch can be used to detect the switch position and event like single click/double click/long press, etc

Capacitive Touch Slider Sensor (CY8C4014LQI) is a multifunctional touch sensor. You can touch the two buttons or slide on the 5-segment s...

The Grove - Micro Switch is a simple, low cost micro switch that integrated the plug-and-play Grove connectors

Grove - Recorder is based on ISD1820P, which can record 8~20 sec by set resistor and cycle play.

This is the latest version of Grove-recorder, and also the best version.

The Grove RS-485 allows your Arduino connect with RS-485 device easily, you just need to plug and play.  

The Grove Starter kit for Azure IoT Edge is a joint-effort developed by Microsoft and Seeed Studio.

Grove Starter Kit for Seeed Studio XIAO assembles the Seeed Studio XIAO series compatible Expansion board, various kinds of Grove modules, c