Hardware and Software products

The LIS2DW12 is a low-power high-performance three-axis linear accelerometer, featuring low power(50nA), low noise(1.3mgRMS), 32 FIFO...

The Flora Bluefruit LE makes it easy to add Bluetooth Low Energy connectivity to your Flora.

A pair of Flower brooches connected via BLE, with vibration, LEDs and touch sensing, that lets you interact with your loved ones.

FOVEA is a wearable embedded analyzer -- a multimeter targeted at embedded electronics with wrist-worn convenience.

Open hardware for sound-based projects using your own custom sound content. Perfect for toys, games, cosplay, art projects, and robots.

This is the FreeSoC2 Development Board, SparkFun’s take on the PSoC5LP ARM Cortex. The PSoC (Programmable System on a Chip) brings togeth...

32-bit general-purpose, high-performance, and low-power MCU powered by the ARM® Cortex®-M3 core

gen4 2.4" Diablo16 Intelligent Display Modules, Resistive Touch, without Cover Lens Bezel

gen4 2.8" Diablo16 Intelligent Display Module,Resistive Touch, without Cover Lens Bezel

triple-network WiFi, BLE and cellular LTE-CAT M1/NB1 MicroPython enabled IoT development board

The concentration of carbon dioxide (0.03% usuallly) is related to daily life.

This is an Arduino compatible piezo film vibration sensor. It is made up of flexible piezo film and converter board.

This is a small form factor IR camera capable of tracking up to four heat/IR sources.

The MMA7361 from Freescale is a very nice IMU sensor with easy analog interface.

This sensor is based on non-dispersive infrared (NDIR) technology and has good selectivity and oxygen-free dependency.

Explore proven designs and real-world use cases with GreenPAK Application Notes—your guide to faster, smarter circuit design.

TSSOP-20 socket for the SLG46620 GreenPAK programmable mixed-signal matrix SLG4SA20-65x64 socket adapter 50 SLG46620G IC samples

More cost-effective monochrome backlight derivative for you, i.e.,

The Grove - 1-Wire Thermocouple Amplifier is a thermocouple-to-digital converters with 14-bit resolution and cold-junction compensation.

This module is based on a 2-Coil Latching Relay

12 bit, digital, triaxial acceleration sensor with smart on-chip motion and position-triggered interrupt features.

The Grove - 6-Axis Accelerometer&Gyroscope(BMI088) is a 6 DoF(degrees of freedom) High-performance Inertial Measurement Unit(IMU) .

Instead of using coil, packaged solid-state relays(SSR) use power semiconductor devices such as thyristors and transistors

The Grove ecosystem has been evolving since the introduction of it and now we are proud to bring you the Grove – Breadboard!

The Electricity sensor module is based on the TA12-200 current transformer which can change large alternating current into a small amplitude

The sensor on Grove - Gesture is PAJ7620U2 that integrates gesture recognition function with general I2C interface into a single chip

The Grove - I2C Motor Driver (TB6612FNG) can drive two DC motors up to 12V/1.2A or drive one stepper motor up to 12V/1.2A

A 9 Degrees of Freedom IMU (Inertial measurement unit) which combines gyroscope, accelerometer and electronic compass.

LED Matrix is low cost and usually used to display simple numbers and images.

Grove - Luminance Sensor using APDS-9002 as lumens Sensor, provide the linear transform lumen intensity for the output voltage levels.

The Grove - Optical Rotary Encoder(TCUT1600X01) is a transmissive sensor that includes an infrared emitter and two phototransistor detectors

Carrying a GrovePi+ board together with 12 carefully selective Grove sensors with 10 pieces cables , this starter kit gets you up and runnin

We integrated 10 full-color RGB LEDs on this stick, with only one signal pin you can control all 10 LEDs easily.

Makes it simple and easy to connect sensors and devices to any 96Boards-compatible base board

The camera can present dynamic thermal images and detect the surrounding temperature from -40℃~300℃.

Grove - Water Atomization is a perfect module for you to quickly DIY a humidifier with Arduino. You can also develop more advanced and inter

This GT2 (2mm) Timing belt is made of Neoprene and has Fiberglass Cords for strength. It's great for your automation projects.

ShieldBuddyTC275 is fitted with the Infineon TC275 32-bit multicore processor on a board following the Arduino standard.

Kit that includes the i.MX8M+ SoM and a dual-camera adapter.

Long range wireless enterprise series sensors

Works like a Wireless push notification transmitters

A very flexible form factor, with a variety of physical sizes

Perfect for anyone who loves tech, wants a new geeky challenge or build their own personal Internet of Things.

Sleek, compact, versatile, powerful. Immerse yourself in the power of the Intel® NUC.

Easily build wireless IoT edge networks to connect things to the cloud.

IWR1443 BoosterPack

JustBoom Player is a beautiful and highly-intuitive interface for playing your music from any source.

Ever built your own computer? With our kit and simple story book you’ll not only build your own powerful computer, you’ll bring it to life!

Add smart light and audio to the SensorTag

A wearable dev board that adds mobile application functionality to your e-textile projects via Bluetooth LE.

The MCP9700 is a small thermistor type temperature sensor

The LilyTiny is a tiny little LilyPad board designed to add flashy functionality to your project without taking up a lot of room. Even th...

Seeed’s LTE CAT.1 Pi HAT is an open source cellular extension modem for Raspberry Pi, based on u-blox LARA-R2xx series.

open source cellular extension modem for Raspberry Pi

Battery Bottom

STAMP IO is an IO expansion board based on the STM32F030 main controller.